1. Chain Microstructure
Stiffness: Chin flexibility, 분자 사이의 거리, Side chain의 flexibility 등의 영향
Chain Flexibility
single chain에서의 rotation이 결정한다. 입체장애로 인하여 Chain flexibility가 낮아지면 Tg는 증가한다.
Flexible side group
Side group에 의하여 분자간의 거리가 증가할 경우 free volume이 증가하고
Background of Experiment
□ Al-Si Alloy
AI + Si = Al-Si Alloy
1. Low melting point
2. light
3. Large heat capacity
4. Insoluble to each other
.
.
.
Result and Analysis - EDS
□ Composition Analysis
Al, Si is almost insoluble to each other at rsoom temperature.
All solid phase will have either 100% Al phase or 100% Si phase.
4. Condition
If reflow, IMC layer occurs between the solder ball and substrate. IMC layer's composition changes depending on reflow time.
Temperatuer
255℃
Reflow time
1s, 1min, 5min, 10min, 20min
Experimental conditions
5. Analysis
IMC layer change was observed according to the reflow time.(Reflow time : 1s, 1min, 5min, 10min, 20min). Do refer to
→ ALD is based on the sequential use of a gas phase
chemical process. ALD film growth is self-limited and
based on surface reactions, which makes achieving
atomic scale deposition control possible.
☞ Self-limited growth
☞ Atomic scale deposition
☞ Easy way to produce
uniform, crystalline,
high quality thin films.
-결정성 평가
-FWHM (Full wi
Temperature Modulated DSC(TMDSC), High pressure DSC(HPDSC),
Photo DSC(UV-DSC), Maximum resolution TGA or High resolution TGA(MaxRes TGA or HighRes TGA), Reactor TGA, Dynamic Load TMA(DLTMA), Evolved Gas Analysis or Coupling techniques(EGA or TGA-MS/TGA-FTIR)
Difficult to obtain
reproducibility
A few difference of condition
and temperature
→ Enormous effect on result
→ Hard to
1.1 Soft lithography
Microstructure나 nanostructure을 만들기 위한 printing, molding의 과정을 포함하는 technique으로, 일반적으로 printing, molding, transfer의 3단계 과정을 거친다.
1.1.1 Printing
Master를 만드는 과정이다. Photolithography, e-beam, micro-machining, photoresist 등 다양한 방법을 통해 원하는 모양을 가지는 master를 제작할
Examination of the microstructural image of a specimen magnified by a reflected light microscope from 50x to 1000x in air( or up to 2000x with oil immersion).
Features of metallurgical specimens such as grains, gbs, cracks, ppts can be distinguished because they differ in contrast, caused by the differences in (a) the amount of light absorbed and (b) the inclination of those atomic planes that
* Soil point
S1: 400m (forest) area 0.5㎢
S2: 1100m (forest) area 3.8㎢
( area 3.3㎢ except S1)
S3: 2200m (forest) area 15.2㎢
( area 11.4㎢ except S2)
* Water point
W1 : 900 m
W2 : 3000 m
W3 : 400 m
■ Soil washing the feasibility of applying
1) Low organic matter content2) The suitability of the soil particle size3) The microstructure of the soil water con
Ⅰ. 개요
기존의 분과화된 사회과학의 틀과 분석 전략에서 탈피하려는 문제의식은 대표적으로 월러스틴(Immanuel Wallerstein)에 의해 제기되었다. 그는 근대 이후의 사회현실은 철저히 역사적이고 세계적인 체제라고 전제하고, 이에 대한 연구는 19세기적 사회과학의 패러다임에 의해서 성공적으로 수행
Fatigue Failure Process
균열발생 단계(Crack-Initiation Stage)
공업재료는 연성이며 제조한 상태대로는 균열이 존재하지 않지만, 일반적으로는 입자, 함유물 등을 포함하고 있다고 가정한다. 미시적 크기에서 금속은 균질하지도 않고 등방성도 아니다. 또한 기하학적으로 응력집중(노치)이 되는 부분이 있다